Intimidating, awe-inspiring and travel sized for your convenience, Mushu is now available to download below!
Resin is the recommended print material with this one but I have had relative success printing him on FDM, although his whiskers and thin areas are definitely a struggle to say the least. He is a...
2023-01-31 14:41:08 +0000 UTC View Post
Both versions of the Ornamental Mushu are now available to print below, with and without the gong. The test prints for both versions worked perfectly, printing him solid and 45 degrees to the right as in the previous post.
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT ...
2023-01-29 15:36:18 +0000 UTC View Post
2 successful test prints later and Mushu officially stands and is ready to be printed! I printed him solid to avoid suction issues and at 45 degrees to the right in order to support his chin better. Both STL's are available below, with and without the gong. I printed both versions to make sure they are balanced properly and a...
2023-01-26 03:41:24 +0000 UTC View Post
The ornamental's are finally finished for Mushu, they took a little longer than usual because I had to make them quite small to fit with his long thin, shape, but I'm really happy with the way he's turned out and the test print is currently running. The ornamental model will be out on the page throughout tomorrow along with r...
2023-01-24 02:28:59 +0000 UTC View Post
Mushu appears in Disney's animated feature 'Mulan' as the sidekick and self appointed guardian of Fa Mulan, after he accidentally destroys the great stone dragon. Having originally been demoted to the disgraced position of gong ringer, Mushu's aim in the movie is to help Mulan become a war hero in order to be re...
2023-01-23 00:31:12 +0000 UTC View Post
Starting off this months models I introduced the first villain to the page with the arch nemesis of Cinderella's mice, Lucifer. I had a lot of fun modeling this one, trying to capture his stalking pose and trademark evil smile, and I'm happy to say he's turned out exactly how I planned and I'm really pleased with the end resu...
2023-01-22 23:24:58 +0000 UTC View Post
The second version of Lucifer is attached below and now ready to be printed! rendering took a little longer than I expected so again sorry for the delay. I've also ran a test print which came out perfectly using the same drain hole method as in the previous post.
I've printed him at a massive 23cm length-ways, whi...
2023-01-20 03:47:40 +0000 UTC View Post
Our Lucifer character model is now available below! The model is available in STL format and prints as an individual model.
The model is scaled at 150 x 109 x 96 but is re-scaleable to suit your printing needs. It has been test printed and is suitable for printing on either SLA or FDM printers with extra supports requir...
2023-01-15 02:58:19 +0000 UTC View Post
Its been a long few days working on the ornamental variant but I'm almost finished with the patterning. I'm just in the process of neatening up the final details and then I'll be running the test print so If all goes to plan the Ornamental model should be out on the page sometime tomorrow night along with renders for both ver...
2023-01-12 01:43:43 +0000 UTC View Post
Lucifer appears in 'Cinderella' as Lady Tremaine's villainous black cat. He's sly and cunning and his main goals in the film are to eat one of the main mice, Gus, and to help torment Cinderella.
I've already released a model of Gus onto the page with the intention of making a 2 part model of him a...
2023-01-07 20:02:04 +0000 UTC View Post
Were off to a nice zen start on the page this month when we'll be celebrating Chinese New Year with the beloved pint sized, fire-breathing, guardian of the Fa family, Mushu! I'll also be attempting my first articulated model as well as releasing a printable Mulan inspired zen garden to celebrate the new year, complete with Mu...
2023-01-06 03:02:35 +0000 UTC View Post
This month on the page we celebrated the most magical season of the year with Olaf from Frozen in 2 different poses! I experimented with some transparent resin to create some ice sculpture style models and made a lovely snow globe to add a little magic to this months prints, until I did the unthinkable and dropped it that is....
2023-01-03 04:34:51 +0000 UTC View Post
So did I. As part of the Christmas models I've modeled a plinth and a base with some miniature scenery to make a Frozen themed snow globe for the Christmas models and it was completely finished, but then it did what glass things do when you drop them and unfortunately, no more snow globe.
I've ordered another one ...
2023-01-02 22:54:51 +0000 UTC View Post
There's nothing quite like the smell of freshly baked gingerbread cookies around the house to create that festive feeling, so why not add a sinister twist for all those 'bah humbug!'-ers in your life with the Poison Apple cookie cutter. I decorated mine with a bunch of different Christmas themes to tie in with the holidays bu...
2023-01-01 23:27:34 +0000 UTC View Post
Do you wanna print a snowman? I've got you covered with V2 of Olaf, now available to download below!
What could be better than a living snowman to represent the most magical season of the year? adding a bit of variety this Christmas I decided to model Olaf in two different poses, this one showcasin...
2023-01-01 17:33:22 +0000 UTC View Post
The first of this months holiday themed models is Olaf from Frozen. To add a little variety for Christmas I've modelled him in 2 different poses, one ice skating and one hugging his little snowy friends. Both models printed perfectly on all 3 variants despite the small parts so his hair or arms shouldn't cause any issues for ...
2022-12-24 23:27:46 +0000 UTC View Post
The first of this months holiday themed models is Olaf from Frozen. To add a little variety for Christmas I've modelled him in 2 different poses, one ice skating and one hugging his little snowy friends. Both models printed perfectly on all 3 variants despite the small parts so his hair or arms shouldn't cause any issues for ...
2022-12-24 23:26:55 +0000 UTC View Post
Merry Christmas Patreon! Its officially December on the page, which means Its going to be a busy week for me due to the over run from November. So far I'm happily on track and set to release the first of Decembers models on Christmas eve, alongside some fun Holiday themed treats to mark the occasion!
The photo posts and...
2022-12-21 17:50:55 +0000 UTC View Post
There was a nice short break in between occasions for November so I decided to model two unrelated classic Disney characters, these being Stitch from Lilo and Stitch and of course Gus Gus from Cinderella. Both models have made amazing new additions to the collection and I couldn't be happier with how they've turned out!
The next loveable little critter for our collection plays a vital role in making sure Cinderelly gets to the ball, the adorably dopey new mouse in the house, Gus Gus. I'm always really excited about modelling the classic characters especially the ones you don't see very often, so this one was a lot of fun! once I had eventual...
2022-12-15 21:53:21 +0000 UTC View Post
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT SHAPE SKATE
FDM
LAYER HEIGHT 0.2
INFILL AT 20 PERCENT
STANDARD SUPPORTS
GYROID PATTERN
220 NOZZEL TEMP
60 BED TEMP
65 MM/S
SUPPORT NORMAL / TOUCHING BUILD PLATE
... 2022-12-14 15:31:49 +0000 UTC View Post
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT SHAPE SKATE
FDM
LAYER HEIGHT 0.2
INFILL AT 20 PERCENT
STANDARD SUPPORTS
GYROID PATTERN
220 NOZZEL TEMP
60 BED TEMP
65 MM/S
SUPPORT NORMAL / TOUCHING BUILD PLATE
... 2022-12-14 15:08:52 +0000 UTC View Post
Our Stitch character model is now available below! The model is available in STL format and prints as an individual model.
The model is scaled at 100 x 70 x 70 but is re-scaleable to suit your printing needs. It has been test printed and is suitable for printing on either SLA or FDM printers with extra supports requir...
2022-12-07 01:46:12 +0000 UTC View Post
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT SHAPE SKATE
FDM
LAYER HEIGHT 0.2
INFILL AT 20 PERCENT
STANDARD SUPPORTS
GYROID PATTERN
220 NOZZEL TEMP
60 BED TEMP
65 MM/S
SUPPORT NORMAL / TOUCHING BUILD PLATE
... 2022-11-29 22:40:28 +0000 UTC View Post
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT SHAPE SKATE
FDM
LAYER HEIGHT 0.2
INFILL AT 20 PERCENT
STANDARD SUPPORTS
GYROID PATTERN
220 NOZZEL TEMP
60 BED TEMP
65 MM/S
SUPPORT NORMAL / TOUCHING BUILD PLATE
... 2022-11-29 22:40:01 +0000 UTC View Post
So I've been a bit under the weather the past couple of weeks and I'm a little bit off schedule, the good news is the first set of models are completely finished and will be out late tonight if not Tomorrow. I'm really, really pleased with this one and I can't wait to share it!
The second set of models will be Gus Gus f...
2022-11-29 15:24:13 +0000 UTC View Post
Halloween at Disneyland wouldn't be complete without Tim Burton so this months models were dedicated to 2 of his creepy cute canines, Zero and Sparky. I had so much fun learning a new style and both models have made love-able little additions to the collection.
On the page this month I also introduced a new FDM s...
2022-11-17 19:55:51 +0000 UTC View Post
The second of our Halloween models is the main focus of Tim Burton's beautifully animated sci-fi-horror movie Frankenweenie, none other than Victor Frankenstein's energetic four-legged best friend, Sparky. I really enjoyed working on this model, Tim Burton's uniquely cute and creepy style is so much fun to play around with an...
2022-11-17 17:53:18 +0000 UTC View Post
RESIN
45 DEGREE ANGLE
DENSITY 75 PERCENT
RAFT SHAPE SKATE
FDM
LAYER HEIGHT 0.2
INFILL AT 20 PERCENT
STANDARD SUPPORTS
GYROID PATTERN
220 NOZZEL TEMP
60 BED TEMP
65 MM/S
SUPPORT NORMAL / TOUCHING BUILD PLATE
... 2022-10-31 18:40:19 +0000 UTC View Post
Our Sparky character model is now available to download! The model is available in STL format and prints as an individual model. Sparky is scaled at 100 x 93 x 54 but is re-scaleable to suit your printing needs. It has been test printed and is suitable for printing on either SLA or FDM printers with supports required.
<...
2022-10-31 18:40:07 +0000 UTC View Post
