Included in rev29 of the new Apollo zip here
Stock backplate and direct mount on linear rail options
----
Taichi can be used in bowden or dual direct drive...
2022-12-24 02:55:44 +0000 UTC View Post
Codename "SPEEDSTER"
STL + STEP in the zip
By request, this is built around the Klemco v6 groove mount (get it on amazon)
Ducts are repurposed Apollo ducts, chopped down.
It's rudimentary, just a quick built, no cable mana...
----
edit: files posted : https://www.patreon.com/posts/apollo-mini-dual-79220716
----
Just wondering if there is any interest in dual 4010 instead of 5015
If so let me know
2022-12-12 02:57:05 +0000 UTC
View Post
After two fail print (was playing with very low filament flow for support, didn't work, but also means it was printing in mid air for hours), so was great motivation to get that setup.
This will mount on the chain setup, as pictured.
But the spacing of the mounting holes is the same as the extrusion (20mm), so c...
Here is a printed mount that's easy to install and remove.
uses two M3x8 screws to mount into the Saturn/Apollo Backplate using the sherpa mini model
four M3x6 for the screw between the mount and the LGX lite
Now part of ...
Tweaked the attached two files to accommodate
Apollo on Rails
+Mellow FLY SHT 36 (Very likely the BTT model as well, but haven't actually checked)
+ Orbiter 2.0 (motor facing back)
+ Drag Chain
----
Dec 4 - UPD...
2022-11-25 21:29:06 +0000 UTC View Post
This is very experimental, so be ready to come across issues. (which we can then fix)
There are cutouts for belts, and for the X endstop.
The backplate is standard Apollo (so if you want something other than orbiter 2, get it from the main2022-11-15 03:52:09 +0000 UTC
View Post
Have you ever cut your finger, or splice some wire there, well I come to the rescue! (ok neither of which happened to me, but always kinda bothered me how sharp it was)
Well not much else about it, beside being a snap in place.
Print in PETG preferably (or anything that doesn't snap and break easily) , as it needs t...
The mount was meant for BTT E3RRF + IDEX
BTT E3RRF board has the same mounting point as any E3 board format (stock creality and all E3 iteration for BTT and other vendors , like SKR E3 v1v2v3, etc..)
if you need to bolt it down, just make some holes with the files.<...
-----
Rev2: 4248_rev2.1.zip
-----------
revised model : https://www.patreon.com/posts/81188967
-----------
<...
-----------------------------------------------------------------
-----------------------------------------------------------------
-----------------------------------------------------------------
ApolloLander
2022-09-04 16:32:38 +0000 UTC
View Post
----
Hot threaded insert
m3 x 4mm Length x 5mm Diameter - https://amzn.to/3Z1Rwej
Or
m3 x 4mm Length x 4.6mm Diameter - https://amzn.to/42tuoHu
...
2022-08-27 00:19:13 +0000 UTC View Post
-----
Oct 21: added a belt mount with wider slots
-----
STEP file included
Screw length (might be some small mistake, but should mostly correct)
2x M2x12 (bottom fan screws)
2x M2x8 (top fan screws)
2x M3x6 - flat head - accessories screws included with the hotend
2x M3x25 - hotend mount
Hotend itself STEP file not included as it's under NDA, once released you can get it from Phaetus website
Also added a bunch of additional mounting point for accessories and such because why not! never know when these can come in handy.
Besides the 4 stock motor mounting screw holes, the other mounting holes are as usual meant for heat inserts M3, 4mm long, 4.6mm or 5mm OD.
As for the sensor use ...
2022-08-16 03:13:54 +0000 UTC View Post
Just an idea, open to any suggestions.
Secure the adxl to this with M3x4 screws, place the screws and put a little pressure as you screw in until the screw grabs the plastic, then you'll be able to get it tight.
edit: added a version with threaded screw holes, should make it easier to screw them (edit:tweaked the th...
Update: installed on my machine and it works great!
(I uploaded new alignment tools as the top mounted rail model were too long for this.)
Stock Y endstop switch can stay in place (at least on ender3v2), and should activate at roughly the same Y position as stock setup.
may not work on ender3 ...
-----
May 31:
small update (no need to reprint if you did) - backplate_1of2.stl had mesh errors which usually the slicer can fix without issues, but fixed it anyway, and updated the step file as well
thanks to GentSimps for finding a temporary possible X endstop mount.
2022-05-31 04:31:07 +0000 UTC
View Post
Hi all, first of all I want to thank every single one of you for supporting my work! It means a lot, and appreciate it so much!!!
I will be away for most of June (visiting family followed by my honeymoon), so I paused the patronage for June, you will still have access to all the files. (new patron can still sign up)
Made to use with those little pneumatic fitting (aka bowden collet) as pictured
2022-05-28 05:05:44 +0000 UTC View Post
I needed something asap, so it's nothing fancy, and not extensively tested.
Not sure if there is any interest for this, but decided to post it anyway.
my only requirements were that it snapped shut, easy enough to reopen and screws didn't jump compartments when closed. If full and you shake it violently upside down w...
2022-05-15 17:49:22 +0000 UTC View Post
Updated bltouch model Aug15 2022
----
By request, here is a front mounted bltouch
use screws (M3x8) and M3 nuts to secure the bltouch and longer screws for top mounted fans screws anything between M3x25 and M3x30
offset X = 0
BLTOUCH
2022-05-11 16:47:41 +0000 UTC
View Post
-----
June 3
Added STEP file for ender3/pro/v2, with two sizes, shorter one for use with longer than stock replacement belts and longer one to use the stock belt. so you can mod things to your liking. This can definitely be improved and eventually will do so. but in the meantime you can too.<...
I don't recommend using this with the Apollo, as the Apollo has direct mount to front mounted rail (unlike the Saturn)
For a top mounted rail the Apollo support the wambam plate.
-------
Aug 8th:
This will keep being updated. Mostly links.
If you find anything interesting feel free to post in the comment below.
To locate Raspberry Pi in stock: https://rpilocator.com
The Basics:
Might work on other printers, not sure of their setup
The Stock extruder motor (42-40) has a bit more torque than the Y stock (42-32) so if you ever experienced Y skips this will help, otherwise not really a needed upgrade.
The stock Y mount won't work with a larger motor as it will hit the bed ...
klipper will work on all board, even stock, you just need a Raspberry Pi or Orange Pi or similar and connected via USB or via 3 GPIO pins (using UART)
WHAT IS SCREWS_TILT_ADJUST ? you ask
It allows to use the probe to level the bed by probing above each bed leve...
2022-04-06 19:27:19 +0000 UTC View Post
If you want to test another hotend with your ender6 let me know.
Right duct confirmed working! Thanks to Merkaba for all the testing!!!
Body is good too
---
updates
APR 25:
Those stock tension wheels can be annoyingly small (approximately 18mm diameter), so here is a larger variant that will still fit under the moving bed on a ender3v2
You can either use a M4 6mmOD 10mm long heat inserts, or extract the one from the original tension wheel ...
2022-03-19 16:15:16 +0000 UTC View Post
